HF trailer resto

News, events, issues/items of the day. Does not need to be MV specific.

HF trailer resto

Postby pfarber » Sat Jul 02, 2016 1:04 pm

It was time to repaint and upgrade my HF trailer. I got the 1100lb 4-lug version a few years ago and it was showing its age... so time for a resto.

First tip... the paint on the frame varied from peeling off rusted to almost a .5mm thick. If you have the option to pay to get it sandblasted DO IT. My sandblasting setup is not that bad and it took me, on average, over an hour to get to bare metal. Its not that the frame was rusty... but the paint was just so thick. I'd happily pay $100 to have someone sandblast the frame. Its not a lot of metal.. but the inside channels and thick paint made it pretty miserable.

Next the rust. There were two significant rust patches. Both were on the 'A' arms, near the quick fold pins. Not sure why this was the most rusted spot.

This is after sandblasting and priming (I was doing this on the cheap.. I had a half gallon of red oxide left so that's what I used). Note how pitted the metal is. Definitely needs repaired.
I used an propane/O2 torch to burn the paint off, then a wire wheel and then mineral spirits to clean the metal.
t1.PNG
t1.PNG (981.65 KiB) Viewed 8636 times


MiG'd over the pits.
t2.PNG
t2.PNG (521.2 KiB) Viewed 8636 times


Ground down
t3.PNG
t3.PNG (650.41 KiB) Viewed 8636 times


Side shot showing flange back to original thickness. Also you can see part of the other A frame repair. Same spot.
t4.PNG
t4.PNG (600.88 KiB) Viewed 8636 times


First of many coats of Rustoleum Enamel in Red. I really hated this paint. It was a bitch to spray and took forever to dry.
t5.PNG
t5.PNG (471.46 KiB) Viewed 8636 times


There were a few other minor rust areas.. the A frames had the worst. I think the frame will be good for a while as the frame was sandblasted clean, phosphated, primed, then painted.

I also upgraded to LED lights and made some light covers.. will add that in a few days.
I got a Mountain Cur and a ~~pitbull~~ big loveable cuddle puppy
RIP Kimber 5/26/2022
RIP Yeager 1/3/2019
RIP TJ 3/25/2014
RIP Sugar Bear 8/29/2014
RIP Shilo 4/10/2015
RIP Yuki 2/19/2017
User avatar
pfarber
Motor Sergeant
 
Posts: 2839
Joined: Wed Oct 10, 2007 2:45 am
Location: The Internet

Re: HF trailer resto

Postby pfarber » Sun Jul 03, 2016 8:40 pm

Sere here are my side marker LEDs. Bought them off Amazon, 5 lights for $8

To protect them (they always seem to be the first to break) I make a U channel from some tube steel I had laying around.

20160703_183641.jpg
20160703_183641.jpg (76.84 KiB) Viewed 8632 times


Cut off the top, bevel the sides, and phosphate/prime/paint

20160703_183655.jpg
20160703_183655.jpg (86.7 KiB) Viewed 8632 times


The new marker lights had the exact same mounting holes as the original trailer lights... so they fit right into the same holes

20160703_183704.jpg
20160703_183704.jpg (79.27 KiB) Viewed 8632 times
I got a Mountain Cur and a ~~pitbull~~ big loveable cuddle puppy
RIP Kimber 5/26/2022
RIP Yeager 1/3/2019
RIP TJ 3/25/2014
RIP Sugar Bear 8/29/2014
RIP Shilo 4/10/2015
RIP Yuki 2/19/2017
User avatar
pfarber
Motor Sergeant
 
Posts: 2839
Joined: Wed Oct 10, 2007 2:45 am
Location: The Internet

Re: HF trailer resto

Postby pfarber » Sun Jul 03, 2016 8:48 pm

Brake lights were a bigger challenge. Bought flush mount LED lights to replace the shitty side mount lights you get in the $20 kits. They are easily damaged and the lights always seem to need fiddeled with to make a good ground. New LEDs from Amazon ($22 for a set of 2) had a ground lead.. no more frame grounds!

This is my U housing. I made it from L channel welded together. The flanges were 3in x 2in so I welded them together, phosphated/primed/painted. I only had flat black in a rattle can, so that's that color they got.

20160703_183951.jpg
20160703_183951.jpg (113.21 KiB) Viewed 8632 times


Mark the mounting holes and hole for the wires

20160703_184012.jpg
20160703_184012.jpg (113.38 KiB) Viewed 8632 times


Use bracket as a template for mounting holes

20160703_184246.jpg
20160703_184246.jpg (93.14 KiB) Viewed 8632 times


Drilling out the wire hole... drilled 2 1/2in circles and filed them into an oval

20160703_184722.jpg
20160703_184722.jpg (87.99 KiB) Viewed 8632 times


Test fit and enlarge as needed

20160703_185652.jpg
20160703_185652.jpg (101.61 KiB) Viewed 8632 times


Final light mounted

20160703_190755.jpg
20160703_190755.jpg (99.87 KiB) Viewed 8632 times

20160703_190803.jpg
20160703_190803.jpg (103.06 KiB) Viewed 8632 times


All that's left now is the license plate holder. That will be centered on rear end.
I got a Mountain Cur and a ~~pitbull~~ big loveable cuddle puppy
RIP Kimber 5/26/2022
RIP Yeager 1/3/2019
RIP TJ 3/25/2014
RIP Sugar Bear 8/29/2014
RIP Shilo 4/10/2015
RIP Yuki 2/19/2017
User avatar
pfarber
Motor Sergeant
 
Posts: 2839
Joined: Wed Oct 10, 2007 2:45 am
Location: The Internet


Return to Off-Topic